In stock
R8G (Type R1135) 1296 cm³ engine (Page 2 sur 3)
Suitable for:
Simca 1000 / 1200S / R1 / R2 / R3 / CG - Ref 22089M
Renault R8 / R8G / Floride / Caravelle
Alpine GT4 / A110 (1100Cm³ / 1300cm³)
Matradjet
These bearings are only suitable for old generation water...
In stock
Water pump support with thread ( M18x150 ) for mounting a thermistor or a thermal contact.
Out of stock
Out of stock
In stock
In stock
For mounting a belt width: 13mm
In stock
For mounting a belt width: 13mm
In stock
A steel fret is fitted on the surface of the oil seal for better sealing and reduced wear on the pulley.
For fitting a belt width: 13mm
In stock
Out of stock
In stock
This lighter is suitable for:
- R8G / A110 (1108cc / 1255cc / 1296cc)
Kit to be used with a primary resistance coil between 2.5 and 3.5 ohms
Compatible with AVP4708 and AVP4715 coils
In stock
In stock
Pressure: 0 - 6 bar
Release pressure: 0.60 bar
Thread: M14x150
To be mounted with ref AVP5091 for R5 Alpine engine (1223)
In stock
In stock
In stock
Height from oil pump mating face to bottom of strainer: 140 mm
Out of stock
In stock
In stock
Oil pan depth: distance from the gasket surface to the bottom of the pan: 147 mm,
Sold with 3 gaskets and 3 drain plugs.
In stock
Also suitable for replacing the M18x150 probe on the AVP4204 water pump bracket
In stock
Length: 60mm
Possibility of adaptation on other engines without oil filter
In stock
For tightening the oil filter plate on the engine block
In stock
Inlet / outlet connection: BSP 1/2" x14 (x2)
Threaded sleeve: male Ø3/4" - 16UNF and female Ø3/4" - 16UNF
Please note, the oil filter plate does not correspond to the original hoses and fittings. Provide for the...
In stock
In stock
Please note this hose cannot replace the original oil hoses, use only to carry out an adaptable assembly using a connector and a new radiator.
Material: Black synthetic braid
Maximum operating pressure 35 bar and...
In stock
Please note this hose cannot replace the original oil hoses, use only to carry out an adaptable assembly using a connector and a new radiator.
Material: Black synthetic braid
Maximum operating pressure 35 bar and...
In stock
In stock
In stock
In stock
In stock
In stock
HTX COLLECTION 20W-50 oil is a personalized solution for
old and recent collector's vehicles whose engines have been
restored to original condition with or without turbocharger, in particular
those that have been...
In stock
HTX COLLECTION 20W-50 oil is a personalized solution for
old and recent collector's vehicles whose engines have been
restored to original condition with or without turbocharger, in particular
those that have been...
In stock
HTX PRESTIGE 20W-50 oil is a mineral engine oil suitable for
to old and new classic cars.
Thanks to its high viscosity, HTX PRESTIGE 20W-50 guarantees a film
constant oil, even in hot weather, to offer the best...
In stock
In stock
In stock
Sealing of engine and crankcase gaskets, flat gaskets, pipes, threaded fittings, valves, flanges, tanks, cisterns, retention tanks and all mechanical parts
Recommended for fitting old copper-type cylinder head...
Out of stock
In stock
x1 pot of fine grain 240 lapping paste
x1 pot of coarse grain 120 lapping paste
In stock
Only delivery in France
Epoxy coating for the interior of the engine block.
0.5kg of resin and hardener
0.5l of thinner
In stock