Suitable for WEBER 40DCOE and 45DCOE carburetors
M5X22 screws
Sold individually, requires 9 pieces for one carburetor
Number 5 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Pièces Détachées Carburateur Weber 45 DCOM
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors,
For 23g or 26g brass or plastic float,
Requires 1 piece per carburetor,
Number 72 on the exploded view,
Also suitable for the following carburetors: DCOE, DCO/SP,...
In stock
In some configurations, Weber DCOE carburetors are positioned directly above the exhaust, which can create vapor lock problems due to heat: our AVP48010 plate can solve this problem
Plate can be covered with thermal...
In stock
In stock
In stock
M12 Banjo Bolt
Sold individually without gasket
Number 70 on exploded view
In stock
Banjo screw M12
Sold individually without gasket
In stock
Sold individually, 1 required per carburetor,
Number 4 on exploded view
In stock
For M12 banjo bolts
Number 70 on exploded view
In stock
For M12 banjo bolts
Number 98 on exploded view
In stock
Gasket dimensions: Ø 20x12x1mm
Suitable for WEBER 40DCOE and 45DCOE carburetors
Number 2 and number 69 on exploded view
Sold individually, 1 piece required for one carburetor
Compatible with other WEBER carburetors,...
In stock
Joint dimensions: Ø 20x16x1mm
In stock
The kit consists of:
"T" fuel connector x1
90° elbow fuel connector x1
Banjo connector screw x2
Banjo screw under head seal x2
Banjo screw lower seal x2
Hose clamp: Size 12-14mm x3
In stock
The kit consists of:
90° elbow fuel connector x1
Banjo connector screw x1
Banjo screw under head gasket x1
Banjo screw lower gasket x1
Hose clamp: Size 12-14mm x1
In stock
In stock
In stock
Throttle control lever for TWO WEBER 40DCOE AND WEBER 45DCOE carburetors
Allows carburetor synchronization
Suitable for R8 Gordini, Alpine A110, Simca Rallye
8mm diameter ball joint
In stock
Levier de commande d'accélérateur pour UN carburateur WEBER 40DCOE ET 45DCOE
Adaptable sur R8 et Alpine A110 avec pipe pour un carburateur WEBER
Dimension du centre de l'arbre au centre de la rotule: 23,50 mm
Rotule...
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
M5x32 screw
Head width 8mm
Number 52 on exploded view
Compatible with other WEBER carburetors, see below
In stock
In stock
In stock
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
External mounting
Fixes to the carburetor cover
In stock
Suitable for WEBER 45DCOE carburetor
Extension length from the carburetor = 48mm
Stud/nut mounting
Allows installation of AVP high-performance filter part number 48101 or 48102
Also suitable for AVP sock filter part...
In stock
Aluminum air intake horn/trumpet for WEBER 45DCOE carburetor
48mm extension over the carburetor
Stud/nut mounting
Allows installation of high-performance filter REF 48101 or 48102
Also suitable for AVP sock filter...
In stock
Air intake horn/trumpet for WEBER 45DCOE carburetor,
Extension length from the carburetor: 62mm,
ATTENTION: Must be installed with venturi REF 48086,
Fixing with kit REF 48098,
Suitable for mounting AVP filters REF...
In stock
M6x23
Number 23 on exploded view
In stock
Air intake trumpet filter for WEBER 45DCOE carburetor
Fitment possible on all AVP trumpets
Mesh filters that feature two layers of stainless steel mesh with a filter layer in between to ensure maximum engine...
In stock
Suitable for Weber DCOE 45 carburetor air intake horn/trumpet
Fixed with a screw collar on a rubber flange for a perfect seal
Can be fitted to all AVP DCOE45 air intake horns/trumpets
Overall length: 115mm
Diameter:...
In stock
Installation possible on all AVP horns
Length 115mm (can be cut to size)
Clamp included
Sold in pairs
In stock
In stock
In stock
Kit of 4 springs for locking the venturi in the body of the WEBER DCOE 40 and DCOE 45 carburetor
For first generation Caburator WEBER
In stock
WARNING: Suitable for Venturi ref 48085 and ref 48086 for WEBER 40DCOE and 45DCOE carburetors.
Allows you to stop the movement of the venturi for older generation DCOEs, and stop the movement of the nozzle and...
In stock
Brake for venturi locking screw for carburettor WEBER 40DCOE and 45DCOE latest generation
Number 24 on exploded view
In stock
Idle speed adjustment screw spring for WEBER 40DCOE and 45DCOE
sold individually, ,eed 2 pieces for one carburettor
Part number 47 on the exploded view
Fits other WEBER carburettors, see below
In stock
M9
Sold individually, 2 required per carburetor
Number 48 on exploded view
In stock
Suitable for WEBER 40DCOE and 45DCOE carburettor
Sold individually, need 2 pieces for one carburettor
Number 63 on exploded view
Also suitable for the following carburettors: 38/40/42/45/48 DCOE, 48/50/55 DCO/SP, 45...
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Sold individualy, requires 2 pieces per carburetor
Number 32 on the exploded view
Compatible with other WEBER carburetors, see below
In stock
Suitable for WEBER 40DCOE, 45DCOE and IDF carburetors
Sold individually, requires 2 pieces per carburetor
Number 31 on the exploded view
Compatible with other WEBER carburetors, see below
In stock
Axle for carburetor WEBER 40DCOE old generation
ATTENTION mounts with flat screw REF 48052
Drilling for recovery pump control to be done
Length 180mm overall
Number 85 on exploded view
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Number 78 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Suitable for WEBER 40DCOE AND 45DCOE carburetors
This fits on the side opposite the throttle control
Part number 86 on exploded view
Also suitable for: 30 IBA, 32 IBA, 36 DCNF, 36 DCNFA, 36 DCNV, 36 DCNVA, 38 DCOE,...
In stock
Suitable for new generation WEBER carburetors
Flat type screw (not tapered)
Sold infividually, requires 4 pieces for 1 carburetor
Number 35 on exploded view
Compatible with other WEBER carburetors, see below.
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors old generation for the throttle screw,
Suitable for all types of WEBER 40 and 45 DCOE carburetors for the inspection hatch,
Sold individually,
Countersunk head and...
In stock
Shifting washer against throttle shaft bearing for carburettor WEBER 40DCOE AND WEBER 45DCOE
Thickness: 0.5mm
Inner Ø: 7mm
Outer Ø: 14mm
Number 77 on exploded view
In stock
In stock
In stock
Choke filter for WEBER 40DCOE and 45DCOE carburetors
Requires 1 piece per carburetor
Part number 87 on exploded view
Also suitable for: 35 DCNL, 36 DCNF, 36 DCNFA, 38 DCNL, 40 DCNF, 40 DCNL, 38 DCOE, 40 DCOE, 42...
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
M4X16 screw
Sold individually, requires 2 pieces for one carburetor
Number 40 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Number 74 in exploded view
Also suitable for carburetors: 34 DCHE, 36 DCS, 40 DCOM, 45 MCHH22.
In stock
Fuel pressure gauge kit.
Allows fuel pressure adjustment with the "King" filter REF 6825.
Graduation from 0.20g up to 1 bar.
With connector and clamp for 6 or 8 diameter flexible hoses.
The pressure gauge can be...
In stock
Allows easy adjustment of the float with one side of the tool calibrated to 5mm and the other to 6mm.
Allows direct action on the float tab thanks to a slot at the end of the tool
In stock
Allows easy adjustment of the float with one side of the tool calibrated to 8mm and the other side to 9mm.
Allows direct action on the float tab thanks to a slot at the end of the tool.
In stock
Allows control of nozzle calibration
Graduation is 0.05 mm in 0.05 mm increments, with a minimum of 0.45 mm and a maximum of 1.5 mm.
In stock
Allows control of nozzle calibration
Graduation is 0.10 mm in 0.10 mm increments, with a minimum of 1.5 mm to 3.00 mm and a maximum of 1.5 mm.
In stock
Synchronizer/Synchrometer to be placed directly in the air intake horn for timing adjustment
Suitable for all AVP air intake horns
Graduation from 1-30kg/h
In stock
Sold with drill bit holderIncludes 5 drill bits in each of the following sizes:0.6mm0.7mm0.8mm0.9mm1.0mm1.1mm1.2mm1.3mm1.4mm1.5mm1.6mm1.8mm2.0mm2.1mm2.2mm2.3mm2.4mm2.5 mm2.6mm2.8mm3.0mm3.2mm
In stock
In stock
This paste is suitable for petroleum-derived hydrocarbons (mineral oils, petroleum, fuel oil, leaded and unleaded gasoline, etc.), chlorinated solvents, diluted acids and bases
Replaces or is used in combination with...
In stock
In stock
F9 emulsion tube for WEBER 40DCOE and 45DCOE
Number 13 on exploded view
Also suitable for Weber carburetors: 32 DATR, 32 DRTA, 32 DMTRA, 48 DCOSP, 50 DCOSP, 55 DCOSP, 38 DCNL, 38 DCN, 40 DCNL, 40 DCOM, 45 DCO3, 45...
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Number 13 on exploded view
Also suitable for Weber carburetors: 32 DATR, 32 DRTA, 32 DMTRA, 48 DCOSP, 50 DCOSP, 55 DCOSP, 38 DCNL, 38 DCN, 40 DCNL, 40 DCOM, 45 DCO3,...
In stock
In stock
Accelerator pump cap for WEBER 40DCOE and 45DCOE carburettor
Sold individually, need 2 pieces for one carburettor
Number 59 on exploded view
Compatible with other WEBER carburettors, see below
In stock
Suitable for WEBER 40DCOE and 45DCOE carburettors
Sold individually, need 2 pieces for one carburettor
Number 58 on exploded view
Compatible with other WEBER carburettors, see below
In stock
Fit for WEBER 40DCOE and 45DCOE Carburetor
Sold individually, need 2 pieces for one carburetor
Part number 58 on exploded view
Compatible with other carburetors WEBER, see below
In stock
In stock
In stock
In stock
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Thickness 0.70 mm, super-fittable
Number 66 on exploded view
Compatible with other WEBER carburetors, see below
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock