2mm longer rod for recut camshafts.
Length: Intake 168mm
191mm exhaust
In stock
Alpine GT4 Engine and Transmission Performance
Our performance and Racing spare parts for your Alpine GT4
Discover here a wide selection of parts and accessories designed to improve and boost the performance of your Alpine GT4 1108cm³ engine or your Alpine GT4 1255cm³ engine.
Whether you are looking for an aluminum crankshaft pulley, aluminum rocker cover, oil pump, push rod, oil filter connector for oil cooler or even a water pump pulley, high flow water pump, racing clutch kit, aluminum pipe for weber carburetor, carburetor flange, green air filter, distributor, electronic ignition kit...at AVP, Arnaud Ventoux Pièces, you will find everything you need to optimize the operation of your old one with quality components.
Out of stock
In stock
In stock
In stock
In stock
Height of the joint plane / bottom of the strainer: 140mm
In stock
Length: 60mm
Possibility of adaptation on other engines without oil filter
In stock
For tightening the oil filter plate on the engine block
In stock
Inlet / outlet connection: BSP 1/2" x14 (x2)
Threaded sleeve: male Ø3/4" - 16UNF / female Ø3/4" - 16UNF
Please note, the oil filter plate does not correspond to the original hoses and fittings. Provide for the...
In stock
In stock
Please note this hose cannot replace the original oil hoses, use only to carry out an adaptable assembly using a connector and a new radiator.
Material: Black synthetic braid
Maximum operating pressure 35 bar and...
In stock
Please note this hose cannot replace the original oil hoses, use only to carry out an adaptable assembly using a connector and a new radiator.
Material: Black synthetic braid
Maximum operating pressure 35 bar and...
In stock
In stock
In stock
In stock
In stock
In stock
Out of stock
In stock
In stock
R8G / A110 (1255 cc /1296 cc ) Centering pins to be removed
R5 Alpine (1223)
R5 Alpine Turbo (122B)
Out of stock
Out of stock
Suitable for "original ball thrust bearing" type assembly or for conversion with a guided thrust bearing
Out of stock
Brass scabbard that replaces the original plastic one.
Out of stock
In stock
In stock
Out of stock
Delivered with these O-rings (x4) and these paper seals (x4)
In stock
In stock
In stock
In stock
In stock
This lighter is suitable for:
- R8G / A110 (1108cc / 1255cc / 1296cc)
Kit to be used with a primary resistance coil between 2.5 and 3.5 ohms
Compatible with AVP4708 and AVP4715 coils
In stock
Suitable for:
- R4 - R6 - R8 - Caravelle - Matra jet - R12.TL - R12.TS - R15.TL - A110.V85 (810) - A110.GT4
- Type 688 / 689 / 810 engine
This igniter is to be used with a primary resistance coil between 2.5 and 3.5...
Out of stock
Kit to be used with a coil of primary resistance between 2.5 and 3.5 ohms
Compatible with coils AVP4708 and AVP4715
Compatible for Ducellier igniter with an internal body diameter of Ø 58.8mm
Not suitable for an...
In stock
Kit to be used with a coil of primary resistance between 2.5 and 3.5 ohms
Compatible with coils AVP4708 and AVP4715
Compatible for Ducellier igniter with an inner body diameter of Ø 58.8mm
Not suitable for an igniter...
In stock
In stock
- Integrated short extensions
- Straight coil terminals
- Spool wire length: 50cm
In stock
- Integrated short extensions
- Straight coil terminals
- Spool wire length: 50cm
In stock
Suitable for:
R8.G (1255cc and 1296cc Engine)
GT4 / Matradjet (1255cc Engine)
A110 1100G and 1300G
A110.1600 S / SC / SI
A310.4 1600VF (Injection) / R12.G / R17.G
Super 5GT Turbo
In stock
Out of stock
Flange with inner cone Ø 35mm and outer Ø 53mm
In stock